| |
|
| |
| Noise |
Microphone
Equivalent Input Noise
Measured at ST bus output, 22Hz-22kHz band, RMS. IP termination
= 200ohm. |
| Gain
+60dB |
<-127dBu |
Line
Input/Output noise
Measured at ST bus output, 22Hz-22kHz band, RMS. |
| Unity
gain |
Typically -86dBu |
Mix
Noise From 24 Mono Channels
Channels 1-24 assigned to the stereo bus, 22Hz-22kHz band, RMS.
|
| Unity
gain |
0.001% |
Index
| Total
Harmonic Distortion |
Mic
Input to Main Output
Measured at ST Bus output, 10K or 600ohm load. Test signal 56dBu
@ 1 kHz, Gain = +4dBu output. 22Hz-22kHz band, RMS. |
| |
<0.06% |
Line
Input to Main Output
Measured at ST Bus output, 10K or 600ohm load. Test signal +4dBu
@ 1kHz, Gain unity. 22Hz-22kHz band, RMS. |
| |
<0.04 % |
Index
|
| |
| Frequency
Response |
Mic
Input to Main Output
All Filters & EQ out. Measured at ST Bus output with 10K load.
Test signal 40dBu, Gain set at 50dB for 10dB output. |
| |
+/-0.5dBu
(20Hz-20kHz)
|
Line
Input to Main Output
All Filters & EQ out. Measured at ST Bus output with 10K load.
Test signal +4dBu, Unity gain. |
| |
+/-1.0dBu
(20Hz-20kHz) |
Index
|
| |
| X-Talk |
Channel
Breakthrough
Mono inputs to Group Outputs. |
| |
Better
than 75dB (20Hz-15kHz) |
| Channel
Pan Cut-Off |
| |
Better
than 65dB (20Hz-20kHz) |
| Fader
Breakthrough |
| |
Better
than 70dB (20Hz-15kHz) |
Index
|
| |
| Headroom |
Mic
Input
Measured at the channel insert point. Gain 10dB. |
| |
>+10dBu
|
Line
Input
Measured at the channel insert point. Gain unity. |
| |
>+24dBu |
Index
|
| |
| Output
Levels |
| Stereo
Bus Output |
| |
>+22dBu |
Index
|
| |
| Impedance
|
Mic
Input
Measured using Audio Precision System One protocol. |
| |
>1k5
@ 1kHz |
Line
Input
Measured using Audio Precision System One protocol. |
| |
>10k
@ 1kHz |
Outputs
Measured using Audio Precision System One protocol. |
| |
<60
ohm @ 1kHz |
Index
|
| |
| Common
Mode Rejection |
| Mic
Inputs |
| |
<-70dB
@ 1kHz |
| Line
Input |
| |
<-50dB
@ 1kHz |
Index
|
| |
| RN-RL1 |
Microphone
Equivalent Input Noise
Measured at ST bus output, 22Hz-22kHz band, RMS. Input terminated
with 200ohm source. Gain +66dB. |
| |
<-128dBu |
Line
Input/Output Noise
Measured at ST Bus output, 22Hz-22kHz band, RMS. Gain unity. |
| |
Typically
-85dBu |
Total
Harmonic Distortion
Mic input to Main output. Measured at ST Bus output with 10K or
600ohm load. Test signal 1kHz, 22Hz-22kHz band, RMS. |
| |
<0.01%
|
Frequency
Response
Mic input to Main output All Filters & EQ out. Measured at ST Bus
output with 10K load. |
| |
+/-0.5dBu
(20Hz-30kHz) |
Headroom
Mic input Measured at the channel insert point. Unity Gain. |
| |
>+24dBu
|
Impedance
Mic Input. Measured using Audio Precision System One protocol.
|
| |
>1k5
@ 1kHz |
Outputs
Measured using Audio Precision System One protocol. |
| |
<60
ohm @ 1kHz |
Common
Mode Rejection
Mic Inputs |
| |
<-70dB
@ 1kHz |
| Direct
Output Symmetry |
| |
<-30dB
@ 1kHz
The slope reaches 12dB per octave. |
Index
| Notes |
Console
Types
All specifications for the Recall console apply to consoles that
are installed completely in accordance with AMEK’s recommendations.
This includes recommendations on power supply cables and grounding.
The figures in this specification are typical figures measured on
a standard 40 position console, immediately after completing normal
production tests. Figures will therefore vary slightly from console
to console and the results here should not be regarded as 'guaranteed
minimum performance'.
Notes:-
1.0dBu = 0.775 Volts.
2.Published specifications apply to standard consoles.
3.All measurements taken using the Audio Precision System One test
set.
4.Where no load impedance is specified, the equipment should be loaded
with 10K ohms or greater.
5.These figures are typical of performance in a normal electromagnetic
environment. Performance may be degraded in severe conditions. |
|
